What are you looking for?

Search sailing, scuba, gear reviews, treasure hunting, and Galley recipes.

Open ocean horizon

Marine Inverter Sizing Guide

Marine Inverter Sizing: Complete Cruising Guide

An inverter converts battery DC power into AC power for devices such as laptops, coffee makers, induction cooktops and some watermakers. Selecting one means planning power, energy, surge requirements and safe wiring—not simply buying the largest wattage advertised.

Open Gypsea Bleu’s Inverter Sizing Calculator →

Worked example: choose power rating separately from battery capacity

Suppose a laptop uses 90 W while a small coffee maker uses 900 W. If both operate together, that is 990 W of continuous AC load before allowance for surge or additional devices. A nominal 1,000 W inverter offers almost no headroom in that scenario, so assess the equipment ratings and expected simultaneous loads rather than relying on a single wattage estimate.

For energy planning, 900 W used for 6 minutes equals 90 Wh of AC energy. At an illustrative 90% inverter efficiency, the battery supplies about 100 Wh, excluding standby draw. Try the Marine Inverter Sizing Calculator, then use the Marine Electrical Load Audit to account for daily consumption.

FAQ: Does a larger inverter always drain batteries faster? Not necessarily under the same load; actual consumption depends on conversion efficiency and idle draw. Compare manufacturer efficiency curves and standby consumption, not just maximum power.

1. Start with an appliance inventory

Record each AC appliance’s measured or manufacturer-rated running watts, likely hours of operation, and starting surge. Distinguish devices that run at the same time from loads used separately. A 1,500W kettle and a 1,500W induction burner do not require 3,000W continuous capacity if you deliberately never run them simultaneously. Conversely, automatically cycling refrigeration can start while another appliance runs.

Example equipment Illustrative running load Planning consideration
Laptop power supply 60–180W Actual use often below adapter rating
Small coffee maker 700–1,200W Heating load, usually little motor surge
Microwave 1,000–1,700W input Use AC input, not cooking-output rating
Induction cooktop 800–1,800W or more Check selectable power levels
Refrigerator compressor Highly variable Starting surge may exceed running watts

These are examples, not equipment specifications. Use actual nameplates or a reliable power meter.

Captain’s Note — Don’t confuse watts and watt-hours

Watts measure how much power an appliance demands now. Watt-hours measure how much energy it consumes over time. A 1,000W appliance operating for 15 minutes uses approximately 250Wh, before inverter losses.

2. Continuous rating versus surge rating

A marine inverter must carry sustained loads without overheating and provide enough short-duration surge for equipment startup. Surge ratings are time-dependent: an inverter advertising 4,000W surge for milliseconds may not start a compressor that needs extra power for seconds. Motor power factor, waveform and manufacturer specifications also matter.

In the calculator, enter continuous AC load as the sum of simultaneous running watts. Enter extra startup surge as the additional watts above that running load which may overlap it. The estimator adds the two; it does not automatically determine motor starting characteristics. Verify the chosen inverter’s surge power and duration.

3. Choosing 12V, 24V or 48V

At equal power, higher DC voltage reduces input current. For a 2,000W AC load at 90% efficiency, estimated DC input current at nominal voltage is approximately 185A at 12V, 93A at 24V, or 46A at 48V. At low battery voltage it will be higher.

A 12V inverter may be entirely suitable for modest loads. Larger systems can benefit from 24V or 48V battery architecture, but switching system voltage may require DC-to-DC converters, appropriately matched charging equipment, and a carefully planned integration with existing 12V services.

Captain’s Note — Minimum voltage governs maximum current

For conductor and equipment planning, use the inverter’s realistic minimum operating battery voltage—not nominal voltage alone. Example: a 1,200W AC load at 90% efficiency and 11V DC requires about 121A.

4. Inverter efficiency and idle consumption

Inverters consume more DC watts than they deliver as AC output. At 90% efficiency, a 900W AC load requires roughly 1,000W DC. Efficiency varies with loading; published peak efficiency may not apply at small loads. An oversized inverter may have significant idle draw, particularly if left operating all day. Check idle watts, search/eco mode behavior, and whether appliances tolerate interrupted standby AC.

5. Estimating battery autonomy

Nominal battery energy in watt-hours is approximately battery volts × battery amp-hours. Apply a conservative usable fraction for the battery chemistry, operating conditions and desired reserve. Then divide usable energy by total DC power demand: AC watts ÷ efficiency + additional direct DC watts.

Worked example: A nominal 12V, 400Ah bank at an assumed 80% usable fraction represents 3,840Wh. A steady 1,200W AC load at 90% inverter efficiency plus 100W of other DC loads consumes about 1,433W, suggesting 2.7 hours of idealized runtime. Actual duration may be shorter due to low-voltage cutoff, high discharge rates, BMS limits, battery condition and ambient temperature. This estimate excludes charging from solar, alternators or generators.

Refrigerators, watermakers and compressors may cycle. For cruising-energy planning, use realistic duty cycles and daily watt-hours rather than assuming nameplate watts run for 24 hours.

6. Step-by-step: using the Gypsea Bleu calculator

  1. Choose battery voltage: 12, 24 or 48V. Check the inverter’s supported DC range.
  2. Enter continuous AC load: Add devices expected to run together.
  3. Enter extra startup surge: Use a measured or documented additional startup requirement, not the full appliance rating twice.
  4. Set headroom: A 15–25% allowance can provide design flexibility, but does not replace manufacturer limits.
  5. Enter inverter efficiency: Use a credible figure near your expected loading—not simply a marketing peak.
  6. Enter minimum DC voltage: Use the realistic lower operating voltage for your bank and inverter.
  7. Add battery Ah and usable fraction: These estimate accessible nominal energy, not guaranteed runtime.
  8. Add additional DC loads: Include simultaneous devices powered directly from the battery bank.
  9. Interpret the result: Compare continuous watts, surge requirements, estimated DC current and runtime against actual equipment specifications.

7. Wiring, fusing and protection

A large inverter can pull hundreds of DC amps. Cable size depends on continuous and surge current, positive-and-negative cable length, permitted voltage drop, insulation temperature rating, installation environment, bundling and equipment terminal requirements. Use the Gypsea Bleu Marine Wire Size Calculator for preliminary planning, then verify the design against applicable ABYC standards and manufacturers’ instructions.

Install correctly rated disconnects and overcurrent protection with sufficient interrupting capacity for the available battery fault current. Lithium battery banks may present high prospective short-circuit current. Also verify busbar ratings, terminations, inverter input current, BMS continuous/peak discharge limits, and battery compatibility.

8. Shore power, generator and AC distribution

An inverter/charger may include shore-power transfer switching and battery charging, but integrating it safely involves neutral-ground switching, equipment grounding, shore-power protection, breaker sizing, AC output arrangement and transfer behavior. Do not backfeed an existing AC panel through an improvised connection. Marine AC work should follow applicable ABYC E-11 requirements and qualified marine electrical practice.

9. Selecting equipment and planning future expansion

Compare pure sine-wave output, continuous rating at installation temperature, surge rating and duration, DC operating range, efficiency across realistic load levels, idle consumption, charger integration, remote monitoring, service support, and installation clearances. Leave room for realistic future needs such as larger refrigeration, Starlink, electric cooking or more substantial AC loads. However, buying significantly more inverter than needed can increase cost and standby consumption.

Captain’s Note — Plan the whole energy system

An inverter does not create energy: it converts it. Before committing to air-conditioning or electric cooking at anchor, evaluate battery capacity, solar production, alternator and shore charging, and what happens after several cloudy days. The Gypsea Bleu Tools page also includes Solar & Battery Sizing, Battery Charging & Generator, and Systems Endurance calculators.

10. Common mistakes to avoid

  • Using a microwave’s cooking-output watts instead of input watts.
  • Confusing advertised surge watts with a guaranteed multi-second motor-start capability.
  • Sizing DC conductors at nominal voltage while ignoring greater current at low battery voltage.
  • Assuming a 3,000W inverter will run a 3,000W load indefinitely under every thermal condition.
  • Using advertised battery amp-hours without applying realistic usable limits, cutoff settings or discharge-rate restrictions.
  • Ignoring inverter idle power and cooling requirements.
  • Neglecting AC transfer, neutral-ground and shore-power safety.

Final pre-installation checklist

Confirm real load measurements, simultaneous-use assumptions, startup surge duration, inverter operating voltage, battery chemistry and BMS limits, battery energy reserve, cable calculations, fuse interrupting capacity, mounting and ventilation, AC integration, and manufacturer-recommended commissioning tests.

Safety note: This guide and calculator are educational planning tools, not an approved electrical design. Follow equipment documentation and applicable ABYC E-11/E-13 standards, and have significant electrical modifications reviewed by a qualified marine electrician.

← Return to the Marine Inverter Sizing Calculator

LET’S KEEP IN TOUCH!

We’d love to keep you updated with our latest news and offers 😎

We don’t spam! Read our privacy policy for more info.